topic Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base. in Nest Thermostats

Nest Thermostat gen3 keeps saying remove from base and then put back on base.

therealfoz — Thu, 24 Oct 2024 12:56:54 GMT

Hi,

My Nest Thermostat is saying to remove from the base - then says to put back on. It's a constant loop.

I've tried holding the ring down to reset, I've tried charging with USB and other suggestions, nothing has worked.

From what I've read it may need a new base plate, but they are no longer available to purchase.

Help!

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

Patrick_Caezza — Fri, 25 Oct 2024 23:29:13 GMT

@therealfoz

How do you have the thermostat wired?

Is there a C wire installed?

Can you post a picture of the thermostat's wiring?

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

therealfoz — Sat, 26 Oct 2024 00:19:35 GMT

Thanks for the reply. Yes I do have a common.
Here’s a pic of the wiring… note my red is unplugged here because I was trying both RC and RH, but it was the same for both.

https://ibb.co/NLVkNyR

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

Guarcax — Tue, 29 Oct 2024 02:42:16 GMT

Hi folks!

@Patrick_Caezza thanks for your assistance.

@therealfoz I’m sorry for the inconveniences that you’ve been experiencing with your Nest Thermostat 3rd generation. I understand that it’s been working with a constant loop that asks you to remove the thermostat from its base and then reattach it. I know you have already followed some troubleshooting steps; you already charged the device using an USB cable and also tried a reset on the device but still not working. No worries, I’m glad to help you in this.

Here are some extra steps for you:

Remove the display from the base.
Perform a hard restart on the thermostat.

Press the thermostat ring until the screen turns off; it could take about 10 seconds.

While the display is detached from the base, wait for the thermostat to turn back on and display the message: “Please attach the display to its base.”

I also will suggest you check the 20-pin connector for any visible damage. Make sure the pins are straight and in good condition.

You can check the following articles for further information: Restart or reset a Nest thermostat.

Tell me how it goes.

Regards,

Daniel.

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

therealfoz — Tue, 29 Oct 2024 02:46:50 GMT

Hi Daniel, thanks for the reply.

i did do a hard reset a little while ago after reading that troubleshooting step on another site.

It seemed to do something.. took awhile to ‘boot’ back up and brought me to the language screen that’s at the beginning of the setup. I hadn’t seed that screen before. However after going through a couple screens of setup it said it needed to shutdown to charge the battery.
This is after I had it charging via USB all night. I’m wondering if the battery is bad in it?

Craig

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

Guarcax — Thu, 31 Oct 2024 01:07:50 GMT

Hi @therealfoz!

Thanks for your reply.
I’m sorry to hear that you are still experiencing the same power issue in your Nest Thermostat 3rd generation even after all the troubleshooting steps you have followed. In order to receive further assistance, please fill out this form with all the necessary information, like the thread title or link and your username in the community. Once you've completed the form, let me know. Someone from my team will contact you shortly to help.

I’ll be waiting for your response.

Regards,

Daniel.

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

therealfoz — Tue, 29 Oct 2024 11:47:35 GMT

Thanks Daniel,

I’ve filled out the form

Cheers,

Craig

Re: Nest Thermostat gen3 keeps saying remove from base and then put back on base.

Guarcax — Thu, 31 Oct 2024 01:07:27 GMT

Hi @therealfoz!

We've received your form and appreciate the details you provided. Please keep an eye on your mailbox and spam, as someone from my team will contact you shortly to help. If you have any questions or concerns in the future, feel free to reply to this post.

Regards,

Daniel.